Sharp YO-370 Instrukcja Obsługi Strona 71
- Strona / 118
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
FTS 370d/w/r Revision 10 – 1/09/2015 59
Site Tower
Configuration
(System 1
only)
Tower Type
Red
White
Dual
Number of Beacons
1
1 - 6
Marker Mode
2
Steady
Flashing
Red Flash Mode
3
Efficiency
Legacy
Flashes Per Minute Red
4
20 FPM
30 FPM
40 FPM
GPS SYNC
Enable/Disable
GPS Delay
5
Load Default Value
Yes /No
Yes Confirm?
0000 ms Valid Range 0-3000
Catenary
3
Yes /No
Dry Contacts
Combined
Separate
PD (Photodiode) Alarm
Disarm
6
On /Off
Auxiliary
Input
7
Help
A Secondary System Can Use The Auxiliary Input To Command Lights
On/Off.
Command
Status On /Off
Control Type
Help
Auxiliary Input Can Be Controlled By Either Modbus Or
Dry Contact, But Not Both.
Disabled
Modbus
Dry Contact
Confirm
Output
Configuration
Help
Choose Which Dry Contact Output To Override With
Auxiliary Input Lights On/Off Command Confirmation.
Disabled
Mode Status
Comm Alarm
GPS Sync. Alarm
Photodiode Alarm
Marker Alarm
Night Alarm
Day Alarm
Heartbeat
8
Range Is 0 - 65535
(Value 100 = 10.0s)
IR Enable
3
Help To enable infrared beacon, the beacon must support IR.
Yes/No
IR Is Night Alarm
Help When selected, an IR alarm will also cause a night alarm.
Yes/No
1. Must be set to “1” when using Auxiliary Input.
2. If “Flashing” is selected, the markers will flash in synchronization with the beacon.
3. “Legacy” mode is operational only when 20 FPM is selected. Red Flash Mode selection is overridden in Catenary mode
or when 30/40 FPM is selected. IR beacons ignore “Legacy” mode.
4. Beacon will flash in “Efficiency” or “Legacy” mode when 20 FPM is selected. Beacon will only flash in “Efficiency”
mode when 30 or 40 FPM is selected.
5. GPS SYNC must be Enabled for GPS Delay menu option to be displayed.
6. The 19 hour mode timer is intended to provide notification of a possible failure in the system. The disarm feature
should only be activated if the system is installed in a location prone to periods of light or darkness that would exceed the
19 hour mode timer.
7. Feature available in Firmware V2.9 and above. “Number Of Beacons” must be set to 1.
8. Used only when Auxiliary Input is controlled by Modbus to provide a fail-safe in the event of a communications failure
between the SC 370 and the external control device.
Note: Verify that the lighting system is programmed to operate as described by the FAA
determination for the structure.
- VANGUARD 1
- FTS 370d, 370w, 370r 1
- System Controller (SC) 370 5
- Flashhead CABLE 5
- Front Matter 7
- Personnel Hazard Warning 8
- Table of Contents 9
- List of Figures 11
- List of Tables 12
- System Overview 13
- Specifications 14
- Operation Overview 16
- PCB1 Controller Board 17
- Manual Override 18
- Status and Alarm LEDs 18
- P2 Auxiliary Input 21
- J4 Communication Cable 21
- Connection 21
- PCB3 Smart Board 22
- GPS Sync. Kit 22
- USB Port 22
- FH 370d/w/r 23
- Controller Installation 26
- Input Power 27
- Photodiode Wiring 27
- Photodiode Mounting 27
- Cellular Antenna 28
- GPS Antenna 29
- Communication Cable Kit 31
- Dry Contact Alarm Outputs 33
- Flashhead Cable 33
- Wiring Procedure 33
- Securing the Cable 34
- Flashhead Installation 37
- DETAIL A 40
- 15.75 (400) 43
- 7.5 (190.5) 43
- KNOCKOUT SIZE DIA 45
- PHOTODIODE 50
- INTERFACE BOX 52
- Standard System 56
- LOW BATT 64
- MARKER INTERFACE 66
- (P/N 2422000) 66
- (P/N 1362034) 66
- The photodiode 68
- Marker Mode 68
- Red Flash Mode 68
- IR Enable 70
- IR Is Night Alarm 70
- Local Tower Config 72
- Local Ethernet Configuration 74
- Primary Data Monitoring 74
- Alternate Data Monitoring 74
- Site Event History 76
- Lighting Inspection (LI) 78
- Mode Override 79
- System Reboot 79
- System X Firmware 79
- USB Firmware Update 80
- Information Display Alarms 80
- Section 4– Web Interface 82
- Auto Fast LI 83
- Manual Fast LI 83
- Manual Staged LI 83
- Auxiliary Input 84
- Tower Lighting 85
- System “X” 86
- Monitoring 87
- SNMP Labels 87
- Cellular Modem 88
- Troubleshooting 90
- Component Removal and 93
- Replacement 93
- EHTERNET 98
- 1 2 3 4 5 98
- Table 6-4 – Marker Interface 100
- Critical 102
- Table A-1 – Critical INFORMs 103
- Table A-2 – Warning INFORMs 104
- Modbus RTU over RS485 106
- Modbus RTU over TCP 106
- Implemented Modbus Map 106
- RMA Policy Revision 2014B 117
- Revision 2014B RMA Policy 118
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji