Sharp YO-370 Instrukcja Obsługi Pobierz pdf (Strona 112)

100 Revision 10 – 1/09/2015 FTS 370d/w/r

Tower Monitoring Interface

Address Read/Write Register Name Description / Values

70 R Tower Status State

254 (Increments

indicate a reportable status event such

as an alarm occurred)

71 R Tower Configuration State

254 (Increments indicate a tower configuration change

occurred)

72 R Controller Alarms/Indications

Bit 0: Indicates system powered up

Bit 1: Indicates power to the tower is off (POWER FAIL)

Bit 2: Reserved

Bit 3: Indicates low tower DC power (LOW DC)

Bit 4: Indicates a photodiode alarm, which is a 19 hour

mode change failure (PD ALARM)

Bit 5: Indicates Tower 485 com failure (SYS COMM)

Bit 6: Indicates GPS sync failure (GPS ALARM)

Bit 7: Indicates that a device has been discovered for which

the system has not been configured (CFG ALARM)

Bit 8: Indicates Override Mode

Bit 9: Indicates system is running a Lighting Inspection

Test (LI TEST MODE)

Bit 10: Reserved

Bit 11: Reserved

Bit 12: Indicates on multi-beacon systems that a failure to

sync has occurred (TWR SYNC)

Bit 13: Indicates that IR (Infrared) is not available or

supported by the attached beacon (IR N/A)

Bit 14: Indicates possible cross talk in PLC communication

(BIND ALARM)

73 R

Controller Alarms/Indications

Changed

Bit mapped alarm indications changed (same bit map as

74 R

Beacon

White Day Alarm

(DAY ALARM)

Bit

set indicates a Beacon 1

White Day

Alarm

respectively

75 R

Beacon White Day Alarms

Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

76 R

Beacon White Night Alarms

(WNIGHT ALARM)

Bit

set indicates a Beacon 1

hite

ight

larm,

respectively

77 R

Beacon White Night Alarms

Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

78 R

Beacon Red Night Alarms

(RNIGHT ALARM)

Bit

set indicates a Beacon 1

ight

larm,

respectively

79 R

Beacon

Red Night Alarms

Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

80 R

Beacon Communication Alarm

(BCN COMM)

Bit

set indicates a Beacon 1

Communication Alarm

respectively

81 R

Beacon Communication Alarm

Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

82 R

Marker Alarms

(MKR ALARM)

Bit

set indicates a Marker Tier 1

larm, respectively

The exact marker which has faulted can be found by

writing the correct value to register 240 and then reading

from register 296.

83 R Marker Alarms Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

84 R

Marker Tier Communication

Alarms (MKR COMM)

Bit

set indicates a Marker Tier 1

Communication

Alarm, respectively

85 R

Marker Tier Communication

Alarms Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

86 R

Current Tower

Lighting

Operating Mode

Day (1), White Night (2), Red Night (3)

87 R

Beacon

Infrared Alarm

(IR ALARM)

Bit

set indicates a Beacon 1

Infrared

larm,

respectively

88 R Beacon Infrared Alarm Changed

Corresponding bits are s

ets to 1 when an alarm transition

occurs. (Reserved)

1 2 ... 107 108 109 110 111 112 113 114 115 116 117 118

Komentarze do niniejszej Instrukcji

Brak uwag

Sharp YO-370 Instrukcja Obsługi Strona 112

Komentarze do niniejszej Instrukcji