Sharp YO-370 Instrukcja Obsługi Strona 67
- Strona / 118
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
FTS 370d/w/r Revision 10 – 1/09/2015 55
Section 3 – Information Display
Navigating the Information Display
Three pushbuttons to the right of the
information display provide access to
navigate the system menus, configure the
system and review diagnostic information.
Table 3-1 describes the function of each
button. The top level menu is described in
Table 3-2. Each menu option is discussed
in the headings following Table 3-2.
Figure 3-1 – Information Display
Table 3-1 – Controller Display Buttons
1
Button Function
S1 UP
Navigates UP through the active menu options.
S2 ENTER
Confirms your selection or Advances to the NEXT option. Press and
hold for 1.5 seconds then release to return to the previous menu.
Press and hold for longer than 5 seconds to return to the main menu.
S3 DOWN
Navigates DOWN through the active menu options.
Table 3-2 – Top Level Menu Options
1
Menu Option
Description
CONTROL TYPE Selects the role of the unit as System 1 or subordinate System 2-6
SITE TOWER CONFIG Selects the overall system configuration. (System 1 only)
LOCAL TOWER CONFIG Selects the individual unit configuration.
MONITORING CONFIG
Selects the type of monitoring equipment that will be used to monitor
the system. (System 1 only)
MONITORING STATUS Provides status of the built in monitoring system. (System 1 only)
LOCAL DIAGNOSTICS
Displays the firmware revision and multiple analog values for the
controller, beacon and markers. This menu is especially helpful when
troubleshooting the system.
LIGHTING INSPECTION
(LI)
Allows the user to perform a lighting inspection. Automatic and Manual
modes are available.
MODE OVERRIDE
Allows the system to be manually placed in any capable mode for a
user definable period of up to 24 hours.
FACTORY TEST Factory use only.
SYSTEM REBOOT
Allows the user to reboot the system without physically interrupting
input power.
FACTORY DIAGNOSTICS Factory use only.
SYSTEM X FIRMWARE
2
(System 1 only)
This feature allows System 1 to display, and if appropriate, upgrade the
firmware version of each connected subordinate unit to its current
version.
2
1. Menu options and features are based on firmware version 3.1.
2. Subordinate units must have firmware Version 3.0 or higher installed to receive firmware upgrade from System 1.
- VANGUARD 1
- FTS 370d, 370w, 370r 1
- System Controller (SC) 370 5
- Flashhead CABLE 5
- Front Matter 7
- Personnel Hazard Warning 8
- Table of Contents 9
- List of Figures 11
- List of Tables 12
- System Overview 13
- Specifications 14
- Operation Overview 16
- PCB1 Controller Board 17
- Manual Override 18
- Status and Alarm LEDs 18
- P2 Auxiliary Input 21
- J4 Communication Cable 21
- Connection 21
- PCB3 Smart Board 22
- GPS Sync. Kit 22
- USB Port 22
- FH 370d/w/r 23
- Controller Installation 26
- Input Power 27
- Photodiode Wiring 27
- Photodiode Mounting 27
- Cellular Antenna 28
- GPS Antenna 29
- Communication Cable Kit 31
- Dry Contact Alarm Outputs 33
- Flashhead Cable 33
- Wiring Procedure 33
- Securing the Cable 34
- Flashhead Installation 37
- DETAIL A 40
- 15.75 (400) 43
- 7.5 (190.5) 43
- KNOCKOUT SIZE DIA 45
- PHOTODIODE 50
- INTERFACE BOX 52
- Standard System 56
- LOW BATT 64
- MARKER INTERFACE 66
- (P/N 2422000) 66
- (P/N 1362034) 66
- The photodiode 68
- Marker Mode 68
- Red Flash Mode 68
- IR Enable 70
- IR Is Night Alarm 70
- Local Tower Config 72
- Local Ethernet Configuration 74
- Primary Data Monitoring 74
- Alternate Data Monitoring 74
- Site Event History 76
- Lighting Inspection (LI) 78
- Mode Override 79
- System Reboot 79
- System X Firmware 79
- USB Firmware Update 80
- Information Display Alarms 80
- Section 4– Web Interface 82
- Auto Fast LI 83
- Manual Fast LI 83
- Manual Staged LI 83
- Auxiliary Input 84
- Tower Lighting 85
- System “X” 86
- Monitoring 87
- SNMP Labels 87
- Cellular Modem 88
- Troubleshooting 90
- Component Removal and 93
- Replacement 93
- EHTERNET 98
- 1 2 3 4 5 98
- Table 6-4 – Marker Interface 100
- Critical 102
- Table A-1 – Critical INFORMs 103
- Table A-2 – Warning INFORMs 104
- Modbus RTU over RS485 106
- Modbus RTU over TCP 106
- Implemented Modbus Map 106
- RMA Policy Revision 2014B 117
- Revision 2014B RMA Policy 118
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji