Sharp AR-CF2 Instrukcja Obsługi Strona 1

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts withspecified ones for maintaining the safet

AR-CF2 OPERATIONAL DESCRIPTION 4 - 66. Paper jam/error detectionA. List of Paper jamsB. Error detection(1) EEPROM errors Explanation:1) Timeout erro

AR-CF2 DISASSEMBLY AND ASSEMBLY 5 - 1[5] DISASSEMBLY AND ASSEMBLY1. Paper Feed Separation UnitA. Pickup Roller & Paper Feed Roller1) Open the to

AR-CF2 DISASSEMBLY AND ASSEMBLY 5 - 22. Paper Feed Unit A. Horizontal Pass Roller 1 and Registration Roller 1) Open the top cover. 2) Open the mount

AR-CF2 DISASSEMBLY AND ASSEMBLY 5 - 35) Remove the finisher latch cover. A: Horizontal pass roller 2 B: Timing roller C. Reverse Roller 1) Open the

AR-CF2 DISASSEMBLY AND ASSEMBLY 5 - 43. Drive Unit A. Belts 1) Open the top cover.2) Remove the rear cover.B. Gears 1) Open the top cover.2) Remove

AR-CF2 MAINTENANCE 6 - 1[6] MAINTENANCE1. Maintenance list ✕ Check ❍ Cleaning ▲ Replace ∆ Adjust ✩ Lubricate ❏ Move position(Clean, replace, an

AR-CF2 TROUBLESHOOTING 7 - 1[7] TROUBLESHOOTINGProblem The inserter does not perform at all when the main switch of the main unit is turned ON. Case

AR-CF2 TROUBLESHOOTING 7 - 2ProblemTray alarm is displayed on the system display. Case1 Cause Sub-tray pulling detection sensor fault Check and reme

AR-CF2 ELECTRICAL SECTION 8 - 1[8] ELECTRICAL SECTION1. Actual Wiring ChartReverse SensorPaper Exit SensorReverse Unit Open/ClosedSensorChassis Cove

AR-CF2 ELECTRICAL SECTION 8 - 22. Circuit DescriptionA. OutlineThis circuit controls paper feed, transport, reverse, and delivery.This circuit consi

AR-CF2 PRODUCT OUTLINE 1 - 1[1] PRODUCT OUTLINEThis inserter is an optional unit for the AR-620 series of digital complexmachines. With the inserte

AR-CF2 ELECTRICAL SECTION 8 - 3C. Circuit Detail(1) Communication Circuit<1> TxD signal <2> RxD signalThis circuit communicates with the

AR-CF2 ELECTRICAL SECTION 8 - 4<2> Paper Exit Sensor (HI_SEN)HI_SEN uses the photointerrupter integrated with an LED and a pho-totransistor.Th

AR-CF2 ELECTRICAL SECTION 8 - 5<9> Paper Width Detection Potentiometer (T_VR)T_VR is a potentiometer.The paper width is detected using the out

AR-CF2 ELECTRICAL SECTION 8 - 6(3) Motor Drive Circuits<1> Paper Feed Motor Drive Circuit (K_MOT)This circuit rotates/stops K_MOT and controls

AR-CF2 ELECTRICAL SECTION 8 - 7(4) Flapper Solenoid and Registration Clutch Drive Circuit (F_SOL and R_CL)This circuit controls the flapper solenoid

AR-CF2 ELECTRICAL SECTION 8 - 8(7) Inrush Current Limiting CircuitThis circuit limits an inrush current flowing into the regeneration capac-itor inc

AR-CF2 ELECTRICAL SECTION 8 - 9(9) Operator Panel CircuitThis is the circuit of the operator panel board.The operator panel drive board turns each o

Memo

Memo

Memo

AR-CF2 EXTERNAL VIEWS AND INTERNAL STRUCTURES 3 - 1[3] EXTERNAL VIEWS AND INTERNAL STRUCTURES1. External components2. Sensors and switches156234No.

LEAD-FREE SOLDERThe PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder

CONTENTSParts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts withspecified ones for maintaining t

AR-CF2 BLOCK DIAGRAM / ブロック図 1 - 1[1] BLOCK DIAGRAM Inserter Main Unit RXD0 SGND TXD0 DC+24VDC+24

AR-CF2 ACTUAL WIRING CHART / 実体配線図 2 - 1[2] ACTUAL WIRING CHART Reverse SensorPaper Exit SensorReverse Unit Open/ClosedSensorChassis Cover Open/Clos

AR-CF2 CIRCUIT DIAGRAM AND PARTS LAYOUT / 回路図と部品配置図 3 - 1[3] CIRCUIT DIAGRAM AND PARTS LAYOUT1. CIRCUIT DIAGRAM Main Unit +24VJAM Cover Open/Closed

AR-CF2 CIRCUIT DIAGRAM AND PARTS LAYOUT / 回路図と部品配置図 3 - 2no-mountingno-mountingno-mountingno-mountingno-mounting no-mountingno-mountingno-mountingno

AR-CF2 CIRCUIT DIAGRAM AND PARTS LAYOUT / 回路図と部品配置図 3 - 32. PARTS LAYOUT A. PARTS SURFACE CN2 CN3 CN1No. No. No.1 H_MOT_*B 1 N.C. 1 K_MOT_A2 H_MOT_B

AR-CF2 CIRCUIT DIAGRAM AND PARTS LAYOUT / 回路図と部品配置図 3 - 4B. SOLDER SURFACE

Memo

Memo

AR-CF2 EXTERNAL VIEWS AND INTERNAL STRUCTURES 3 - 23. Motors, solenoid, and clutch3 HI_SEN Paper exit sensor Photointerrupter Detects that a sheet t

LEAD-FREE SOLDERThe PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder

(Danish) ADVARSEL !Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.Udskiftning må kun ske med batteriaf samme fabrikat og type.Levér det bru

All rights reserved.Printed in Japan.No part of this publication may be reproduced,stored in a retrieval system, or transmitted,in any form or by any

AR-CF2 OPERATIONAL DESCRIPTION 4 - 1[4] OPERATIONAL DESCRIPTION1. StructureA. Cross-sectional view (Main body)B. Drive system[List of actuators]2. F

AR-CF2 OPERATIONAL DESCRIPTION 4 - 2B. Normal paper feed operation of inserter (online/offline) [Paper loading]Step 01: A sheet is placed in the pap

AR-CF2 OPERATIONAL DESCRIPTION 4 - 3C. Reverse paper feeding operation of inserter (online)[Paper loading]Step 01: A sheet is placed in the paper fe

AR-CF2 OPERATIONAL DESCRIPTION 4 - 4[Exiting from reverse section]Step 17: When the reverse motor has completely stopped, the reversemotor starts to

AR-CF2 OPERATIONAL DESCRIPTION 4 - 5The correspondence between the punching/stapling mode settings and LEDs is shown below.∗ ●: means "Lit.&quo