Sharp IQ-8000 Instrukcja Instalacji Strona 91
- Strona / 125
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
8.8 User Selectable Options
Underlined settings are for LiNC-NET User -Selectable Options.
An asterisk (*) designates the factory preset jumper settings.
XWIA
XWIA
DCE*
DCE*
DCE*
XWIB
XWIB
DTE
DTE
DTE
W8
W8
A-B
A-B
A-B
4-wire
B-C*
B-C*
B-C*
2-wire
W15
W15
A-B
A-B
A-B
RTS/CD enabled
B-C*
B-C*
B-C*
Data enabled (Maximum speed is 64K)
W5
W5
A-B
A-B
A-B
RTS/CTS* delay (normal)
B-C*
B-C*
B-C*
RTS/CTS/CD delay (CTS inhibited if CD is present when RTS is raised.
W9
W9
RTS/CTS delay (The time before the RS-485 driver is enabled and CTS is
asserted after RTS is asserted. The RS-485 driver is always enabled.)
A
A
A
30 msec
B
B
B
10 msec
C*
C*
C*
0 msec
D
D
D
ON
W17
W17
When W15 is in the B-C (Data Enabled) position, this is the time the RS-485
driver remains enabled after a low-to-high transition on the DATA line to
prevent disabling the driver in the middle of a character.
When W15 is in the B-C (Data Enabled) position, this is the time the RS-485
driver remains enabled after a low-to-high transition on the DATA line to
prevent disabling the driver in the middle of a character.
When W15 is in the B-C (Data Enabled) position, this is the time the RS-485
driver remains enabled after a low-to-high transition on the DATA line to
prevent disabling the driver in the middle of a character.
A
70 msec
70 msec
70 msec
B
7 msec
7 msec
7 msec
C
2 msec
2 msec
2 msec
D
0.7 msec
0.7 msec
0.7 msec
E*
0.15 msec
0.15 msec
0.15 msec
W16
W16
Turnaround delay (When W8 is in the B-C [2 wire] position, this is the time
after the driver is disabled and before the receiver is enabled.)
Turnaround delay (When W8 is in the B-C [2 wire] position, this is the time
after the driver is disabled and before the receiver is enabled.)
Turnaround delay (When W8 is in the B-C [2 wire] position, this is the time
after the driver is disabled and before the receiver is enabled.)
A
0 msec
0 msec
0 msec
B*
msec
msec
msec
C*
msec
msec
msec
D
5 msec
5 msec
5 msec
E
35 msec
35 msec
35 msec
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
S1
S1
OUT*
OUT*
Normal
Normal
IN
IN
Loopback
Loopback
S2
S2
OFF*
OFF*
RS-485 Receiver Unterminated
RS-485 Receiver Unterminated
ON
ON
RS-485 Terminated
RS-485 Terminated
S3
OFF*
OFF*
OFF*
Line Bias Off
Line Bias Off
Page lxxviii of 110 IQ-400 Installation Manual 33-10057-001-C
- Installation Manual 1
- 33-10057-001 1
- 0.1 Board Diagrams 3
- 0.1.4 OUT Expansion Board 6
- 0.1.5 ALM Expansion Board 7
- 0.1.6 SAM Board 8
- 0.2 Table of Contents 9
- 1.0 Introduction 14
- 2.0 Unpacking the IQ-400 16
- IQ-400 - Expansion Cable Plug 19
- 3.0 Installing Power 20
- 4.0 Wiring Your Readers 24
- 4.3.1 Procedure 25
- 4.4.1 Procedure 28
- 4.4.2.1 Procedure 28
- 5.0 Reader Connections 29
- Option 1 34
- Option 2 35
- – Option 2 37
- IQ-400 Board 38
- Expansion Board 39
- 6.0 Wiring the Door(s) 46
- 6.6.3 SAM Board LED Arrays 56
- Exit Sense Inputs 59
- 6.10.1 Procedure 61
- 7.1 Reset the IQ-400 Panel 62
- 7.5 Changing the Baud Rate 69
- PCSC P/N: 04-10318-101 73
- PCSC P/N: 04-10318-001 73
- HyperTerminal 76
- Protocol) 77
- 7.10.2 Installation 78
- 7.10.3 Optical Transmission 80
- 8.1 Status Lights 81
- 8.2 Communication Errors 82
- 8.2.2 Error Codes 83
- (Pins 2-3) 86
- 8.8 User Selectable Options 91
- 8.9 Point Definitions 93
- 8.9.1 Sense Inputs 93
- S3 through S6 are 94
- IQ 4 PCB 94
- 8.9.2 Outputs 96
- Connector 96
- 9.1 IQ-400 Features 99
- 9.1.3 Spare Parts- IQ-400 PCB 100
- 9.2.1 Electrical Ratings 101
- 9.2.2 Power Supply 101
- 9.2.3 Door Sense LEDs 102
- 9.2.5 Jumpers 102
- 9.3.2 System Capacities 104
- 9.3.3 Electrical Ratings 104
- 9.4.1 Electrical Ratings 106
- 9.4.2 Power Supply 106
- 9.4.3 Door Sense LEDs 107
- 9.4.5 Jumpers 107
- 9.5.1 System Capacities 109
- 9.5.2 Electrical Ratings 109
- 9.6.1 System Capacities 111
- 9.6.2 Electrical Ratings 111
- 9.6.3 Spare Parts- OUT PCB 111
- 9.7.1 System Capacities 112
- 9.7.2 Electrical Ratings 112
- 9.8 SAM Board 113
- 4-wire PCSC 114
- 5-wire Wiegand 114
- 9.10 Tool Requirements 115
- 10.1.1 Required Equipment: 118
- 10.1.2 Required Information: 118
- 10.1.3 Required firmware: 118
- 10.3.1 TCP/IP Configuration 121
- 10.4 Resetting the IQ-400E 124
- End of Manual 125
- PCSC, Inc 125
- August 2008 125
Powiązane produkty i podręczniki dla Elementy urządzeń bezpieczeństwa Sharp IQ-8000
(14 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji