Sharp AN-CM270 Instrukcja Użytkownika Strona 1

* Size rounded off to the nearest footBUILDING DIMENSIONSCAUTION: SOME PARTS HAVE SHARP EDGES. CAREMUST BE TAKEN WHEN HANDLING THE VARIOUS PIECESTO AV

The rear roof channel assembly at-taches to the permanent structure andsupports the unit.1 Fasten the channel braces to theend of the rear roof channe

The anchor brackets in this step willbe used later to anchor the unit to thebase/foundation.1 Position an anchor bracket insidethe left & right po

Step 3BO12● Parts Needed For ●Mounting Rear RoofChannel to Structure12●●●●● Rear Roof Channel Assembly (one)● ● ● ● ● 66627 Weather Seal1/2x 1 1/2 (13

Step 3 continued...BO133 Attaching It is important that the rear roof channel be securely anchored to a sound and flat mountingsurface. A special mou

Step 4BO14● Parts Needed For ● Roof ChannelAssembly14Get help holding post in place whileattaching the roof channel.1 Position a roof channel, with sm

Step 4 continued...BO1515STEP2STEP397339660 Right Post9660 Right Post 1 1/8"(2,9 cm)9656

1 Place front facia over front roofchannel with largest amount of holeson top. Fasten bottom flange with five#10Ax 3/8" (10 mm) screws. Fastentop

Step 6BO17● Parts Needed For ●Corner/Front SpliceTrim●●●●● 9670 Corner Trim (four)●●●●● 9669 Front Splice Trim (two)171 If a special mounting board wa

2 Fasten top of right roof panelusing two #10-32x7/16" (11 mm) boltsand square nuts into bottom flange,on rear roof channel. Fasten bottomof pan

Step 7 continued...BO1919Do not fasten until next stepSTEP3STEP4STEP5STEP2#10-32x3/4"(19 mm) Bolt #10-32 Well-Nut2x4(38 mm x 89 mm)2x4ENDVI

2Owner's ManualBefore beginning construction, check local building codes regarding footings, locationand other requirements. Study and understand

Step 8BO20● Parts Needed For ●Top Left and RightEnd Trim●●●●● 9667 Top Left End Trim (one)●●●●● 9668 Top Right End Trim (one)201 Fasten top right end

Step 9BO21● Parts Needed For ●Top Front Trim1 Position top front trim to ends ofroof panels, overlapping top left andright end trim and fasten using s

Step 10 Leveling and Anchoring PostsBO22Check to be sure front facia and rearroof channel are still square. Leveleach post. Stand at one end andvis

If the locality where you have installedthe patio cover/carport could benefitfrom a guttering system, we recom-mend the following list of materials,(n

PC1010 BO241. Avoid nicking or scraping the coating surface,inside and out.2. Keep roof and post perimeter free of debris andleaves which may accum

3Selecting and Preparing Your Site: Before assembly, you will want to decide ona location for your unit. The best location is a level area with good d

4Safety precautions are important to follow throughout the construction of your patio cover/carport•Care must be taken when handling variouspieces of

Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immedia

Foundation Recommendations BO06The Foundation For Your Patio Cover/CarportNote: Before beginning construction, check local building codes regarding fo

Hardware BO07664333/8-16 Hex Nut (2)765106#10-32 Square Nut (30)(Packed with Screws)66624#10-32 Well-Nut (10)(Packed with Screws)9669Front Splice

Parts in Carton OneAssembly Part Part Quantity CheckKey No. Number Description in Carton List 1 9654 Right Facia 1 2 9657 Left Facia 1 3 9664 Top

Assembly by Key No. BO099