Sharp CP-C405 Instrukcja Obsługi

SERVICE MANUALSPECIFICATIONSCHASSISMICROFILMTRINITRON® COLOR COMPUTER DISPLAYCPD-200GSD-1HAustralian ModelChinese ModelChassis No. SCC-L07A-APicture t

1-716Customizing Your MonitorPreset and User ModesThe monitor has factory preset modes for the 9 (CPD-100GS) or 10 (CPD-200GS) most popular industry s

1-819Getting StartedAdditional InformationFENESCSymptom Check these itemsScreen image is not centeredor sized properlyEdges of the image arecurvedWhit

CPD-200GS2-1. CABINET REMOVALSECTION 2DISASSEMBLY2-3. D, A AND J BOARDS REMOVAL2-12-2. SERVICE POSITION Cabinet1243 Two screws(+BVTP 4

CPD-200GS2-23 When one side of the rubber cap isseparated from the anode button, theanode-cap can be removed by turningup the rubber cap and pulling u

CPD-200GSWhen replacing parts shown in the table below, the follow-ing operational chacks must be performed as a safety pre-caution against X-ray emis

CPD-200GS● Landing Rough Adjustment1. Enter the full white signal.2. Set the contrast to “CONT”=255.3. Make the screen monogreen.Note: Off the outputs

CPD-200GS4-2Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software andthen

5-1 5-25-35-4SECTION 5DIAGRAMS5-1. BLOCK DIAGRAMS5-2. CIRCUIT BOARDS LOCATION5-3. SCHEMATIC DIAGRAMS ANDPRINTED WIRING BOARDSNote:• All capaci

1 2 3 4 5 6 7 8 9 10111213141516171819202122ABCDEFGHIJKLMNOABCDEFGHIJKLMNO5-5 5-65-75-8(1) Schematic Diagrams of D and J Boards• D BOARD IC801 TDA70

JAUDIO INHEADPONE5-9 5-10 5-11Schematic diagramAAAAA board l(d)POWERDEFLECTION— J BOARD —— D BOARD —A1BCDE234567• D BOARD SEMICONDUCTOR LOCATIONICI

CDP-200GS– 2 –POWER SAVING FUNCTION DIAGNOSISTIMING SPECIFICATIONMODE AT PRODUCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 MODE 9

1 2 3 4 5 6 7 8 9 10111213141516171819ABCDEFGHIJ5-125-13 5-14Ref. Pin No. Voltage [V]• A BOARD VOLTAGE LISTIC001 1 4.62 4.53 1.84 1.85 2.16 3.48 3.4

5-15— A BOARD —CBA321• A BOARD SEMICONDUCTOR LOCATIONICIC001 B–1IC002 A–2IC003 C–2IC004 A–3IC005 B–3IC006 C–1TRANSISTOR*Q001 C–3 –Q004 C–2 1DIODE*D0

5-165-4. SEMICONDUCTORS

5-17

CPD-200GS• Items marked " * " are not stocked sincethey are seldom required for routineservice. Some delay should beanticipated when orderin

CPD-200GS6-2. PACKING MATERIALS6-2The components identified by shading and mark ¡ are critical for safety. Replace only with part number specified.RE

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

CPD-200GS– 3 –TABLE OF CONTENTSSection Title Page1. GENERAL... 1-12. DISASSEMBLY2-1. C

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARKThe components identified by shading and mark ¡ are critical for safety. Replac

SECTION 1GENERALThe operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Opera

1-27Getting StartedFENESCGetting StartedConnecting Your Monitor’sSpeakerYou can listen to music, sounds, and other audio files usingthe speaker in you

1-39Getting StartedFENESCCustomizing Your MonitorUsing the CENTER On-screenDisplayThe CENTER settings allow you to adjust the centering ofthe picture.

1-410Customizing Your MonitorUsing the GEOM (Geometry) On-screen DisplayThe GEOM (geometry) settings allow you to adjust theshape and orientation of t

1-513Getting StartedCustomizing Your MonitorFENESC4Press the >?// buttons to adjust the settings.The OSD automatically disappears after about 30 se

1-615Getting StartedCustomizing Your MonitorFENESCResetting the AdjustmentsResetting an adjustment item1 Press the MENU, ¨./> and >?//buttons to