11
Type No. Catalog
Number O.D. Hole Teeth Number
42-VTC 1/2” 1/8” 12 TUNSV42
17-VTC 1/2” 3/16” 12 TUNSV17
65-VTC 3/4” 5/16” 14 TUNSV65
75-VTC 7/8” 5/16” 16 TUNSV75
4-VTC 1” 9/32” 18 TUNSV4
85-VTC 1” 5/16” 18 TUNSV85
86-VTC 1” 3/8” 18 TUNSV86
95-VTC 1-1/8” 5/16” 20 TUNSV95
96-VTC 1-1/8” 3/8” 20 TUNSV96
105-VTC 1-1/4” 5/16” 22 TUNSV105
106-VTC 1-1/4” 3/8” 22 TUNSV106
116-VTC 1-3/8” 3/8” 22 TUNSV116
See “General” discussion of Undercutting Saws on page 10.
SAWS (“U”-Slot)
Actual size illustrations; specifications below. Thickness ranges as
follows:
1/4” - 9/16” O.D. from .010” to .045” thick
5/8” - 1-3/8” O.D. from .010” to .065” thick
Be sure to specify thicknesses.
V-CUTTERS (“V”-Slot)
Actual size illustrations; specifications below. Thickness ranges as
follows:
1/2” O.D. from .030” to .045” thick
3/4” - 1-3/8” O.D. from .030” to .065” thick
Angles between cutting edges can be 40°, 50°, and 60°. 40° V-cutters
are for thin mica, 50° for medium mica, 60° for thick mica.
Be sure to specify thicknesses and angle, 40°, 50° or 60°.
COMPOUND-LAND SAWS
The compound-land feature, sketched at right, is available
on tungsten-carbide “U”-slot saws 9/16” O.D. and up (#18-TC
thru #116-TC) at a 30% premium in price. Because of this
feature, each tooth cuts only 50% of full slot width, resulting
in better chip clearance, cooler operation and production
increases of up to 60% over the square-toothed Saw. To
order, add “CL” to Catalog Number. Minimum thickness .015”.
Type No. Catalog
Number O.D. Hole Teeth Number
10-TC 1/4” 1/8” 12 TUNS10
9-1/2-TC 5/16” 1/8” 14 TUNS9.5
32-TC 3/8” 1/8” 14 TUNS32
33-TC 3/8” 3/16” 14 TUNS33
12-TC 7/16” 1/8” 14 TUNS12
42-TC 1/2” 1/8” 14 TUNS42
16-TC 1/2” 3/16” 14 TUNS16
18-TC 9/16” 1/4” 16 TUNS18
54-TC 5/8” 1/4” 16 TUNS54
64-TC 3/4” 1/4” 18 TUNS64
65-TC 3/4” 5/16” 18 TUNS65
75-TC 7/8” 5/16” 20 TUNS75
4-TC 1” 9/32” 20 TUNS4
84-TC 1” 1/4” 20 TUNS84
85-TC 1” 5/16” 20 TUNS85
86-TC 1” 3/8” 20 TUNS86
95-TC 1-1/8” 5/16” 22 TUNS95
96-TC 1-1/8” 3/8” 22 TUNS96
105-TC 1-1/4” 5/16” 24 TUNS105
106-TC 1-1/4” 3/8” 24 TUNS106
108-TC 1-1/4” 1/2” 24 TUNS108
116-TC 1-3/8” 3/8” 24 TUNS116
SPECIALS — Your inquiries are invited for sizes not listed on
the H.S.S. or Tungsten-Carbide Saw Pages.
TUNGSTEN-CARBIDE SAWS and V-CUTTERS
The teeth of both saws and V-cutters have a slight land to give strength to
the cutting edge. Saws are hollow-ground for clearance, V-cutters have
ample radial relief. When Carbide Saws are used on other equipment than
our undercutters, steel supporting washers are recommended to reduce
breakage. Spindle speeds may vary from 3,000 to 12,000 r.p.m., depending
on Saw O.D. Martindale Carbide Saw Blades are harder than High Speed
Steel Saws, therefore more brittle and should not be subjected to apllications
where shock may shorten the service life. Use on rigid stationary equipment.
See Undercutters for 9 Martindale Undercutters for use with these saws:
Close-Cut, Kut-Kwik, Utility, Bench-Type Model HV-3, Lathe-Type and Super
Lathe-Type, Heavy-Duty Bench-Type Model H-9, Industrial Model HA-2, and
Model UL Lathe Mounted Automatic.
(17 strony)
(20 strony)
(20 strony)
(1 strony)
(224 strony)
(1 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji