Sharp AL-1451 Dokumentacja Strona 69
- Strona / 126
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
AL-1551 ADJUSTMENTS 9-5
2) Set the copy magnification ratio to 100%.
3) Make a copy on A4 or 81/2" x 11" paper.
4) Measure the length of the copied scale image.
5) Calculate the main scanning direction magnification ratio.
Main scanning direction magnification ratio
6) Check that the copy magnification ratio is within the specified range.
If it is not within the specified range, perform the following
procedures.
7) Execute SIM 48-1 to select the main scanning direction copy
magnification ratio adjustment mode.
To select the adjustment mode, use the copy mode select key.
In the case of the automatic adjustment, when the PRINT switch is
pressed, the mirror base unit moves to the white plate for shading to
scan the width of the reference line, calculating the correction value and
displaying and storing this value.
After execution of the automatic adjustment, go out from the simulation
mode and make a copy to check the magnification ratio.
If the magnification ratio is not in the specified range (100±1.0%),
manually adjust as follows.
8) Set the adjustment mode to Manual with the copy mode select key.
9) Enter the new set value of main scanning direction copy
magnification ratio with the copy quantity set key, and press the
COPY button.
10) Change the set value and repeat the adjustment until the ratio is
within the speoified range.
When the set value is changed by 1, the magnification ratio is
changed by 0.1%.
(3) Sub scanning direction copy magnification ratio
a. Note
Before performing this adjustment, the following adjustments must have
been completed. If not, this adjustment cannot be performed properly.
•Image distortion adjustment
•Must be installed to the lens unit reference position.
b. Cases when the adjustment is required
1) When the lens and the mirror unit are disassembled or the part is
replaced.
2) When the scanner unit drive section is disassembled or the part is
replaced.
3) When the main PWB is replaced.
4) When the EEPROM in the main PWB is replaced.
5) When "U2" trouble occurs.
6) When the copy image distortion adjustment is performed.
c. Necessary tools
•Screwdriver (+)
•Scale
d. Adjustment procedure
1) Set the scale on the document table as shown below. (Use a long
scale for precise adjustment.)
2) Set the copy magnification ratio to 100%.
3) Make a copy on A4 or 81/2" x 11" paper.
4) Measure the length of the copied scale image.
5) Calculate the sub scanning direction copy magnification ratio.
Sub scanning direction copy magnification ratio
=
Copy image dimensions
X 100 (%)
Original dimension
Adjustment mode Lighting lamp
Main scanning direction auto copy
magnification ratio adjustment
Auto exposure lamp ON
Main scanning direction manual copy
magnification ratio adjustment
Manual exposure lamp ON
Sub scanning direction copy
magnification ratio adjustment
Photo exposure lamp ON
100 110 120 130
150
140
mm
1/2mm
JAPAN
HARDDENCD
STAINLESS
Shizuoka
100
110
120 130
150
140
mm
1/2mm
JAPAN
HARDDENCD
STAINLESS
Shiz uoka
110
10 20
10
20
(When a 100mm scale is used as the original.)
Paper feed
direction
Reference
Comparison point
Original (Scale)
Copy
=
Copy image dimensions
X 100 (%)
Original dimension
100
110 120 130
150
140
mm
1/2mm
JAPAN
HARDDENCD
STAINLESS
Shizuoka
100
110 120
130
150
140
mm
1/2mm
JAPAN
HARDDENCD
STAINLESS
Shiz uoka
110
10
20
10 20
Original (Scale)
Paper feed
direction
Reference
Comparison point
Copy
- DIGITAL COPIER 1
- CAUTION 2
- CONTENTS 4
- [1] GENERAL 5
- [2] SPECIFICATIONS 6
- 3. Copy performance 8
- 4. Printer specifications 9
- [3] CONSUMABLE PARTS 10
- Production control 11
- 1. Appearance 12
- 2. Internal 12
- 1234567 891011 12 13
- 181716151413 13
- (AL-1551) 13
- 4. Motors and solenoids 14
- 5. Sensors and switches 15
- 6. PWB unit 16
- 7. Cross sectional view 17
- 1. Copier installation 18
- 2. Cautions on handling 18
- 4. Unpacking 19
- 4 or 5 times 20
- Paper guide (B) 20
- Paper guide (A) 20
- 8. Power to copier 21
- B. Windows 98: 22
- C. Windows Me/Windows 2000: 22
- D. Windows 3.1x: 22
- 10.Parallel interface 23
- [6] COPY PROCESS 24
- 2. Outline of print process 25
- 3. Actual print process 25
- About DC 5.2kV 26
- Process controlling 27
- [7] OPERATIONAL DESCRIPTIONS 28
- 2. Scanner section 29
- No Component Function 30
- (1) Heat roller 31
- (2) Separator pawl 31
- (3) Thermal control 31
- (4) Fusing resistor 31
- 7. SPF section 35
- C. Operational descriptions 36
- A. Initial state 36
- B. Front copy 36
- Upper Side of Gate 37
- Gate OFF 37
- Transfer 38
- Lock pawl rear 38
- Lock pawl front 38
- 2. Operation panel section 39
- 3. Optical section 40
- Thermistor 41
- PPD2 sensor 42
- Hearter lamp 42
- Heat roller 43
- B. Disassembly procedure 44
- Clutch unit 48
- Paper feed 48
- Wire treatment 49
- 7. Rear frame section 52
- 8. Power section 53
- A. Sensor PWB 54
- B. Pickup solenoid 54
- C. Clutch 54
- F. SPF motor 55
- G. Paper entry sensor 55
- 10.2nd cassette section 56
- D. Transport roller 57
- E. Paper feed clutch 57
- F. 2nd paper feed roller 57
- B. Cassette detection switch 57
- C. Paper feed solenoid 57
- (1) Remove the rear cabinet 58
- (2) Remove the shield plate 58
- (3) Remove the RSPF 59
- (1) Remove the clutch unit 60
- (2) Remove the clutch 60
- J. Transport unit removal 61
- K. Belt 1 61
- (1) Remove the parts 62
- (2) Remove the parts 63
- (1) Remove the reverse gate 64
- (2) Remove the solenoid 64
- Fixing Screws 65
- Set screw 66
- Scanner unit drive pulley 66
- LL and LR: 67
- Distance between the copy 67
- (1) Outline 68
- Shizuoka 69
- (1) Lead edge adjustment 70
- Lens unit number 70
- ( ) direction 70
- Reference line (0) 70
- (+) direction 70
- 2.0mm or less 71
- 2. Copy density adjustment 72
- Non toner 73
- Toner save 73
- The front edge of the 74
- Front edge of paper 74
- [10]SIMULATION, TROUBLE CODES 75
- 2. List of simulations 76
- 4. Trouble codes 88
- [11]USER PROGRAM 89
- [12]ELECTRICAL SECTION 90
- B. MCU PWB unit 91
- (1) CPU signal table 92
- (2) ASIC (Signal table) 94
- 3. Reset circuit 99
- A. Outline 100
- 5. Driver circuit (Solenoid) 101
- 7. Main motor drive circuit 101
- 8. Mirror motor circuit 102
- 9. Duplex motor circuit 102
- A. Block diagram 103
- (1) Main section 104
- (2) FW signal 105
- (3) Heater lamp drive circuit 105
- (4) High voltage section 105
- 11.CL invertor PWB (circuit) 106
- 13.Operation section 107
- [13]CIRCUIT DIAGRAM 108
- AL-1551 CIRCUIT DIAGRAM 13-2 109
- AL-1551 CIRCUIT DIAGRAM 13-3 110
- AL-1551 CIRCUIT DIAGRAM 13-4 111
- AL-1551 CIRCUIT DIAGRAM 13-5 112
- AL-1551 CIRCUIT DIAGRAM 13-6 113
- AL-1551 CIRCUIT DIAGRAM 13-7 114
- AL-1551 CIRCUIT DIAGRAM 13-8 115
- AL-1551 CIRCUIT DIAGRAM 13-9 116
- GDI MEMORY PWB (6MB) 117
- POWER SUPPLY (120V/127V) 118
- POWER SUPPLY (200V Series) 119
- ACTUAL WIRING DIAGRAM 1/5 120
- AL-1551 CIRCUIT DIAGRAM 13-14 121
- AL-1551 CIRCUIT DIAGRAM 13-15 122
- AL-1551 CIRCUIT DIAGRAM 13-16 123
- AL-1551 CIRCUIT DIAGRAM 13-17 124
- CAUTION FOR BATTERY DISPOSAL 125
- COPYRIGHT 126
- 2001 BY SHARP CORPORATION 126
Powiązane produkty i podręczniki dla Urządzenia wielofunkcyjne Sharp AL-1451
Urządzenia wielofunkcyjne Sharp AR-168N Dokumentacja
(177 strony)
(177 strony)
Whirlpool DFG 050 (AG) manuales
Manuales del propietario y guías del usuario para No Whirlpool DFG 050 (AG).
Ofrecemos 1 manuales en pdf Whirlpool DFG 050 (AG) para descargar gratis por tipos de documentos: Instrucciones de uso
Whirlpool DFG 050 (AG) Instrucciones de uso (12 paginas)
Marca: Whirlpool | Categoria: No info | Tamaño: 0.45 MB |
Tabla de contenidos
Más productos y manuales para No Whirlpool
| Modelos | Tipo de documento |
|---|---|
| CVT 146 |
Instrucciones de uso
Whirlpool CVT 146 Benutzerhandbuch,
10 paginas
|
| F080796 |
Guia Energética
Document 9784224 [de] ,
1 paginas
|
| LPA59EI/SL |
Instrucciones de uso
Istruzioni per l`uso,
8 paginas
|
| KRDD 9010 |
Instrucciones de uso
Istruzioni per l`uso,
12 paginas
|
| 5KPEXTA | Instrucciones de uso Whirlpool 5KPEXTA Brugermanual, 15 paginas |
| F086564 |
Guia Energética
Document 9791095,
1 paginas
|
| F084674 |
Guia Energética
Document 9784719,
1 paginas
|
| F077833 |
Guia Energética
Document 9779194,
1 paginas
|
| IWD 6105 (EU) |
Instrucciones de uso
Whirlpool IWD 6105 (EU) Manual de usuario,
24 paginas
|
| BC 312 AAI |
Instrucciones de uso
Whirlpool BC 312 AAI User manual,
40 paginas
|
| IDCA 735 B (EU) |
Instrucciones de uso
 
Whirlpool IDCA 735 B (EU) Manuel utilisateur,
68 paginas
|
| IWDC 6125 C ECO (IT) |
Instrucciones de uso
Whirlpool IWDC 6125 C ECO (IT) Manuale utente,
12 paginas
|
| 5CO |
Instrucciones de uso
Whirlpool 5CO Benutzerhandbuch,
6 paginas
|
| TGA 281/A+ |
Manual de instalación
ISTRUZIONI PER L`USO,
4 paginas
|
| KOHCS 60600 |
Instrucciones de uso
Istruzioni per l`uso,
28 paginas
|
| KMPG 3610 IX |
Instrucciones de uso
Istruzioni per l`uso,
32 paginas
|
| C 3V P6 (W) R /HA |
Instrucciones de uso
Whirlpool C 3V P6 (W) R /HA Benutzerhandbuch,
15 paginas
|
| 5CO |
Instrucciones de uso
Whirlpool 5CO Manuel utilisateur,
6 paginas
|
| 5KN1PS |
Instrucciones de uso
Whirlpool 5KN1PS Manuel utilisateur,
6 paginas
|
| TIAA 12 (1) |
Instrucciones de uso
 
Whirlpool TIAA 12 (1) Manuel utilisateur,
60 paginas
|
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji