Sharp XG-MB67X Przewodnik Szybki Start

MODELXG-MB67XMULTIMEDIA PROJECTORSETUP MANUALConnecting Pin Assignments ... 2RS-232C Specifications and Commands ... 3

-10Setting up the Projector Network Environment12After confirming or setting, proceed to “3. Setting up Network Connection for theProjector”.5 Click “

-11Setting up the Projector Network Environment3. Setting up a NetworkConnection for theProjectorSettings for such items as the projector’s IPaddress

-124 The TCP/IP setting screen ap-pears, ready for network settingsfor the projector.Note• Confirm the existing network’s segment (IPaddress group) to

-13Controlling the Projector via LANControlling the ProjectorUsing Internet Explorer(Version 5.0 or later)Complete connections to external equipmentbe

-14Confirming the ProjectorStatus (Status)On this screen, you can confirm the projectorstatus. You can confirm the following items :••••• MAC Address•

-15Controlling the Projector via LANSetting and Adjusting theProjector (Settings & Adjustments)Example: “Picture” screen display for INPUT 1On the

-16Controlling the Projector via LANMaking General Settingsfor the Network (Network -General)On this screen, you can make general settingsrelating to

-17Controlling the Projector via LANSetting Error Items andDestination Addresses towhich E-mail is to be Sentwhen an Error Occurs(Mail – Recipient Set

-18Setting up the Projector Using RS-232C or TelnetWhen Connecting UsingRS-232C1 Launch general purpose terminalemulator.2 Input settings for the RS-2

-19Setting up the Projector Using RS-232C or TelnetWhen Connecting UsingTelnet1 Click “Start” from the Windows® desk-top and select “Run”.2 Enter “tel

-2RS-232C Terminal: 9-pin mini DIN female connectorPin No. Signal Name I/O Reference1 Not connected2RDReceive Data Input Connected to internal circuit

-20Setting up the Projector Using RS-232C or TelnetSETUP MENU (Main Menu)[1]IP AddressIP address settings. (Page 23)[2]Subnet MaskSubnet mask settings

-21View Setting Detail List([V]View All Setting)11111 Enter “v” and press the “Enter” key.Display all setting values(*).Enter number or symbol of item

-22Save Settings and Quit([S]Save & Quit)Save set values and quit menu.11111 Enter “s” and press the “Enter” key.22222 Enter “y” and press the “En

-23IP Address Setting([1]IP Address)Setting of IP address.11111 Enter “1” and press the “Enter” key.22222 Enter numerical value to be set and press th

-24Password Setting([5]Password)Carrying out security protection using password.11111 Enter “5” and press the “Enter” key.22222 Enter password and pre

-25Disconnecting All Connec-tions ([D]Disconnect All)It is possible to disconnect all the TCP/IP connec-tions currently recognized by the projector. E

-26Carrying out Network PingTest(ADVANCED[5]Network Ping Test)It is possible to confirm that a network connectionbetween the projector and a computer

-27Setting of Search Port(ADVANCED[0]Search Port)Sets the port number used when searching for theprojector from the network.11111 Enter “0” and press

-28Communication cannot be established with the projectorWhen connecting the projector using serial-connection\ Check that the RS-232C terminal of the

-29Troubleshooting\ Ta ke the following steps for checking the network settings for the computer.1. Open a command prompt (MS-DOS Prompt).• In the cas

-3Computer controlA computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,commercially available) to

-30\ Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, checkif an IP address is set.1. Open a command prompt (MS-D

-4RS-232C Specifications and CommandsCommandsExample: When turning on the projector, make the following setting.→←POWR _ 1__ OKProjectorComputerPower

-5RS-232C Specifications and CommandsINPUT 1 Picture Mode : PresentationINPUT 1 Picture Mode : MovieINPUT 1 Picture Mode : GameINPUT 1 Picture Mode :

-6RS-232C Specifications and CommandsINPUT 4 Sharp (ⴑ30 – ⴐ30)INPUT 4 CLR Temp *2INPUT 4 Bright Boost (0 – 2)INPUT 4 Progressive : 2DINPUT 4 Progressi

-7Page 81. Connecting the projector to a computerSetting up the Projector Network EnvironmentThis section describes the basic procedure for using the

-8Setting up the Projector Network Environment1. Connecting the Pro-jector to a ComputerEstablishing a one-to-one connection from theprojector to a co

-9Setting up the Projector Network Environment2. Setting an IP Addressfor the ComputerThe following describes how to make settingsin Windows® XP (Pr