Sharp AR-M208 Instrukcja Obsługi Strona 1

SERVICE MANUALCODE: 00ZARM208/A1EDIGITAL LASER COPIER/ PRINTER(For U.S.A)MODEL AR-M208CONTENTSThis Service Manual describes only the differences from

AR-M208 SPECIFICATIONS 3 - 4∗Top marginThe set value is received from the digital copier, and data are madeaccording to the set value.∗Left marginSinc

AR-M208 CONSUMABLE PARTS 4 - 1[4] CONSUMABLE PARTS1. ListA. SEC/LAG* The other maintenance parts than the above are supplied as service parts.No. Item

AR-M208 EXTERNAL VIEW AND INTERNAL STRUCTURE 6 - 1[6] EXTERNAL VIEW AND INTERNAL STRUCTURE1. External view∗Dehumidification heater switch (DH POWER)T

AR-M208 EXTERNAL VIEW AND INTERNAL STRUCTURE 6 - 25. SensorNo. Name CodeFunction and operation1 Original size sensor DSIN0 Document size detection2 Mi

AR-M208 ADJUSTMENTS 7 - 1[7] ADJUSTMENTS, SETTING2. Copier adjustmentB. Mechanism section(16) SPF scan position auto adjustment[Function]Used to adjus

AR-M208 SIMULATION 8 - 1[8] SIMULATION2. Simulation code list3. DetailsOperation/procedureThe names of the loads which can be operated are displayed.

AR-M208 SIMULATION 8 - 2During execution, [EXEC] is highlighted. Under this state, press the[BACK] key to interrupt the operation.The finisher main mo

AR-M208 SIMULATION 8 - 3The input value is in the increment of –25V.(∗) Linked with the destinations of SIM 26-6.Linked with the auto exposure mode of

AR-M208 SIMULATION 8 - 4*1. The negative value of the set value corresponds to the grid highoutput voltage.*2. The set values can be selected from the

AR-M208 SIMULATION 8 - 5Operation/procedureThe misfeed history is displayed in the sequence of recentness by thename of sensors and detectors. Max. 40

This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC825. This means that thismachine does

AR-M208 SIMULATION 8 - 6The display of the protocol monitor and the soft SW follows this display.When not installed, “- - - - - - - - - -” is displaye

AR-M208 SIMULATION 8 - 7Operation/procedurePress the [OK] key.The scanner mode counter and the number of send of the scanner arecleared.* Execution is

AR-M208 SIMULATION 8 - 8Operation/procedureThe current setup is displayed with ON or OFF.Enter an input (20 digits) of the PS expansion kit soft key a

AR-M208 SIMULATION 8 - 9Operation/procedureTo support an individual necessity in paper and the environment, it isvariable in the range of 5 to 30uA in

AR-M208 SIMULATION 8 - 10• If the auto exposure mode setup value is changed, the setup valueof SIM 46-30 (AE limit setup) is reset to the default valu

AR-M208 SIMULATION 8 - 11Setup of various copy conditions: Similar to the normal copy mode.Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTER

AR-M208 SIMULATION 8 - 12Operation/procedureSelect the mode with the arrow keys, enter the adjustment value withthe 10-key, and press the [OK] key.Whe

AR-M208 SIMULATION 8 - 13[7-seg LED display]1: Self print (2-by-4) mode2: Grid print modePressing the [START] key makes a print by 2 by 4 mode. After

AR-M208 SIMULATION 8 - 14Operation/procedureThe network scanner is checked. When [OK] key is pressed, "Please Send Data" and "READY&quo

AR-M208 DISASSEMBLY, ASSEMBLY AND MAINTENANCE 10 - 1[10] DISASSEMBLY, ASSEMBLY AND MAINTENANCE1. Maintenance tableN: Check (Check, clean, replace or a

IThe AR-M208 is a modified version of the AR-235/275, and is provided with the RSPF and the GDI printer function. (For contents of the RSPF, referto

All rights reserved.Printed.No part of this publication may be reproduced,stored in a retrieval system, or transmitted,in any form or by any means,ele

II[8] 8 - 14 Sim9-5 Default of 2: 1200dpi is changed to disabled. Refer to page 8-1 – 13 of the appendix.Sim21-1 Change/Added (Display, Item, Content,

AR-M208 SYSTEM CONFIGURATION 2 - 1[2] SYSTEM CONFIGURATION1. StructureA. HardwareBlock diagramMirror-MotorSPF/RSPF Unit (Optional)Down-Load-CONSPF-SEN

AR-M208 SYSTEM CONFIGURATION 2 - 22. System outline (Options)For details of the options, refer to the Service Manual of each option.(1) Main unit(2) O

AR-M208 SPECIFICATIONS 3 - 1[3] SPECIFICATIONSThis model is designed as an SPLC printer, and can be extended foruse as a PCL6/PS3/NC/scanner by option

AR-M208 SPECIFICATIONS 3 - 2C. Printer driver specification(1) System(2) Printing function specification(3) System requrementNote: Hardware requiremen

AR-M208 SPECIFICATIONS 3 - 3(5) Paper handling specificationsa. Paper feed directionLimitations on tray/functions for support paper(6) Print enable ar