Sharp AR-C150 Instrukcja Użytkownika

CODE: 00ZARC150/F1EDIGITAL FULLCOLOR COPIERMODEL AR-C150This document has been published to be usedfor after sales service only.The contents are subje

5) Tap the toner cartridge top 5 times, and shake it horizontally 20times. 6) Attach the toner cartridge to the toner box to be refilled.(Example)

D. Paper setup1) Push down the lock lever until it stops to release the tray lock.(AR-C100 only)2) Lift the grip upward, and pull out the paper tray s

2) Remove the cabinet fixing screw.3) Pass the washer of the horizontal level check string into the screw(LX-BZ0870FCZZ) and attach it to the copier.

∗ Perform procedure 1) of ADJ M17 ADJ 3 in the adjustment sectionto check the color balance and the density level.(Note) When performing checking only

[7] SETTING AND ADJUSTMENTS1. List of setup itemsSet itemRelatedsimulationsSET M1 Auto color balance adjustment target setup 46-21,63-7, 63-8SET M2 Au

SET M2 Auto color balance adjustment targetselection There are following two kinds of targets, and one of them can beselected.)(Selection procedure of

ADJUSTMENT ITEM SIMULATIONADJ M16 "Image position, image loss, void areaadjustment"50-1/50-2ADJ M17 Image quality adjustment ADJ 1 CCD gamma

4) Loosen the resist roller fixing screw, and change the resist rollerangle.The standard position is at the center.Repeat procedures 3) – 4) until the

ADJ M7 Image skew adjustment (Scanner(Writing) unit)This adjustment must be performed in the following cases:• When the scanner (writing) unit is repl

Procedures 1) – 4) : Adjustment procedures of the black LSUProcedures 5) – 7) : Adjustment procedures of the color LSUADJ M8 Photoconductor phase adju

AR-C150 Supply List (Europe, Australia, New Zealand)NAME CONTENT(S)LIFENote 1)ModelDIMENSIONS(W × D × H): mm/WHIGHT: kgINCOMPATIBILITY REMARK1 Color T

5) Check the deflection cycle of 125.6mm pitch of four printed pat-terns (C, M, Y). Use the output pattern of the smallest deflectionas the set value

ADJ M9 Main scanning direction copymagnification ratio adjustment(Scanner (Writing) unit)Main scanning direction imageregistration adjustment (Scanner

[How to read the pattern]When deflection is made to the positive (+) side in the rough adjust-ment, increase the value on the positive (+) side.When t

1) Enter the SIM 50-21 mode.2) Select the paper feed cassette of A4R (8 1/2" × 11") paper in thesetup item E (PAPER SEL).∗ Use the paper tra

[Sub scan registration adjustment pattern](Example) Set the simulation set values as shown below.A: 100→Set valueA: 73 (=100 –27)B: 112 B: 129 (=112 +

[How to read the pattern]When deflection is made to the positive (+) side in the rough adjust-ment, increase the value on the positive (+) side.When t

ADJ M17 Image quality adjustmentSTARTPerform ADJ1 CCD gammaadjustment.Copy color balance density check(Check in the TEXT/Photo mode.)(Test chart UKOG-

Copy color balance and density checkCheck the color balance and the density by making copies of Sharpgray chart and the serviceman chart.a. Note for t

While the automatic color balance adjustment by the serviceman al-lows adjustment even when the machine environment is changed lar-gely, providing nor

15) Use the test chart UKOG-0283FCZZ and check the copy colorbalance and the density in Text/Photo mode. (Refer to thesection of the copy color balanc

B.Consumable parts required for setupNo. Name Outside Japan 1 Oil bottle AR-C15SL 2 Developer cartridge (Y)Color developer kit(Y, M, C)Black develo

AR-C150Vorgehensweise zur Kopienqualitätseinstellung1. SIM 63-3 (SIT Chart) oder - CCD Grundeinstellung SIM 63-5 (Standard Werte)2. SIM 63-8 - Stan

AR-C150 Special Tools List Tool Parts Code Price Code NoteColor Test Chart UKOG-0283FCZZ BP

Operation Manual kitLanguage Model name Content NoteEnglish AR-150SE Operation Manual (Boundtogether with Key OperatorGuide), Operation panelsheet25 s

C. Transfer section1) Open the front cover (1), and remove the toner hopper unit (2).2) Remove the toner hopper connector cover (3) in section A andre

7) Remove the unit fixing screw B (1) and the unit fixing screw A (2).8) Remove the fusing front paper guide fixing screw (1) and theprotector (2).Kee

7) Install the electrode section to the original position, and fix it withthe fixing screw.8) Insert the main charger unit fully into the machine alon

B. Developer setup(1) Developer setup 1) Remove the blue screw (1), and remove the DSD holder (2)(3)(4)(5).(Note) A color label is attached to each D

8) Set the developer cartridges in the sequence of black, cyan,magenta, and yellow. 9) Put the developer cartridge on the developer unit pawl A, andp